.st0{fill:#FFFFFF;}

How to replace the battery in a Chrysler 200? 

 September 19, 2021

By  Phil Borges

Chrysler 200's are great cars. They're perfect for commuting, running errands, or taking the family on a road trip. But like any car, they need maintenance to stay in top shape. One of these necessary tasks is replacing the battery when it goes bad. If you're reading this post, the chances are that your Chrysler 200 battery has died, and you want to know how to replace it yourself, then congratulations! You've come to the right place!

How to replace the battery in a Chrysler 200?

Cars are a significant investment, so it's important to get the most out of them for as long as possible. One way to achieve this is by changing your car battery when it starts to die. You might think that changing a car battery is difficult, which is not that much and requires a lot of tools, but there are actually only two things you need: A wrench and a replacement battery.

Before you proceed with the battery replacement, make sure that the engine is turned off. Park your car somewhere safe, with proper ventilation, and ensure that the working area is not around flammable items.

Step 1: For you to access where the battery is, you will need to jack up the driver's front side of the car so you can remove the left front tire. Make sure that the vehicle is in a sturdy position so you can easily remove the wheel.

Step 2: Remove the fender cover/shield by pulling the pushpins that hold the cover in place.

Step 3: Use a 13-millimeter wrench to loosen the bracket bolt and remove the battery hold-down bracket. Do the same procedure to swing down the battery side bracket.

Step 4: For this next procedure, it is best that you wear protective glasses and gloves for your safety. Use a 10-millimeter wrench to loosen the battery negative and positive cable clamps. Then remove the negative cables followed by the positive cable.

Step 5: Once the cables are removed, carefully lift the battery and pull it out from the compartment. You may want to check the compartment to ensure that it's clean and clear.

Step 6: Now, it is time to install the new battery. Make sure that your replacement battery comes with a label on it indicating where the positive and negative terminals should be connected for proper polarity. Reconnect first the positive cable, then the negative one. Use a 10mm wrench to tighten the battery clamp bolts and make sure it's secure enough so the cables won't fall off while you drive.

Step 7: Reattach the battery hold-down bracket back and secure it in place. Don't forget to retighten the fastener of the bracket, as this will keep your battery intact. Do the same procedure in reinstalling back the side battery bracket.

Step 8: Return the cover shield and retighten the screws, and pushpins back in place.

Step 9: Reinstall the front side wheel and secure the lug nuts.

Step 10: Lower down the car from the jack stand and check if everything is working fine.

How long does the battery in a Chrysler 200 last?

The life expectancy for a new Chrysler 200 battery is around 3-5 years, but this depends on driving habits and other factors. There are many ways to extend the battery's lifespan, and these are:

  • With the aid of some cleaning solution and a wire brush, clean the battery terminals and posts to prevent corrosion.
  • Don't allow your battery to go unused for lengthy periods of time.
  • Keep the battery secured and tightly fastened. Vibrations while driving may cause connections to loosen and rattle their components.
  • Ensure to park your vehicle indoors and away from extreme temperature changes or climatic shifts.
  • Schedule the battery for a regular check-up with your mechanic. This way, you can ensure that your battery is in proper working condition.

What are the common signs to watch out for when your battery is dying?

One of the very common signs your battery might be dying is when you try to turn the key in the ignition, it takes longer than usual to roll over or start, or it doesn't start at all.

Another sign is the Check Engine Light comes on. You could also get this warning if there's an electrical issue in your vehicle, and that can cause lots of different symptoms, including dimming lights or Random Starts/Stops.

Fluid leaks around the battery terminals are another sign of a dying battery. In other cases, this might look like a battery is leaking, but the fluid could be from another source, so you better check this out as well.

If your headlights start to dim or flicker at idle and you're driving down the road, that's also a sign of a dying battery.

When these happen, it's best to get your battery checked as soon as possible.

Conclusion

Replacing a battery in a Chrysler 200 is not as difficult of a task as some people might think. In fact, the steps are fairly straightforward and easy to follow. Just make sure that you are using the recommended battery for your vehicle so that your new battery can last as long as possible.

If ever your car's battery has been dying for a while now, or if it just suddenly died on you without any warning signs beforehand, then there may be something wrong with it that must be looked at by an auto mechanic for further inspection. Maintaining your car's battery can prevent a lot of problems from happening in the future.

About the author

Hi, I'm Phil Borges.. thanks for reading.. My wife says I can't shut up about batteries so to save my marriage I've started this blog .. where I'd be ranting about batteries! Please leave a comment if you have any questions, I'm happy to help!

{"email":"Email address invalid","url":"Website address invalid","required":"Required field missing"}
Battery Tools