Batteries are amazing pieces of technology. Under the right circumstances, they can provide voltage and current for extended periods of time without needing to be recharged. However, there are some factors that can reduce a battery's lifespan or performance. One such factor is the reduction in voltage that occurs when a battery is under load. Let's take a closer look at what causes this phenomenon and what you can do to extend your battery's life.
Table des matières
Pourquoi la tension de la batterie baisse-t-elle sous charge ?
One of the main reasons that battery voltage drops under load is because the current passing through the battery causes resistance. This resistance creates heat, which in turn reduces the battery's ability to deliver power. Additionally, as a battery discharges, its internal resistance increases, which also contributes to a voltage drop. Finally, when a battery is heavily loaded, the active materials within the battery start to dissolve, which also reduces its performance. All of these factors work together to cause a voltage drop under load. As a result, it's important to choose a battery that can handle the expected load requirements. Otherwise, you may end up with a battery that doesn't provide enough power when you need it most.
How much should battery voltage drop under load?
This is difficult to answer, as it depends on the individual battery and load. Generally speaking, though, batteries should be kept at or near fully charged levels so that they have enough power when needed.
The amount of voltage drop that occurs under load is determined by the resistance of the wire or cable. The lower the resistance, the less voltage drop there will be. This is why DC Cables are designed with low-resistance wires and connectors so that you can get the most out of your batteries while maintaining a safe level of voltage.
It's important to remember that a good battery is like a good engine. You want to keep it well-tuned so that it's always ready when you need it. Follow these tips to help you get the most out of your batteries:
- Keep your batteries fully charged or at least near full charge levels.
- Use low resistance cables and connectors whenever possible.
- Avoid extreme loads and allow your batteries to cool down after heavy use.
- Regularly test your battery's voltage and performance under load conditions.
By following these tips, you can help ensure that your batteries are always performing at their meilleur.
Why does my voltage drop when load increases?
A battery's voltage drops under load because of the internal resistance of the battery increases. This is caused by the chemical reaction inside the battery that creates electricity. As more current flows through the battery, it becomes harder and harder for electrons to flow from one electrode to another. This increase in resistance causes a drop in voltage. The amount of voltage drop depends on the battery's chemistry and design.
Some batteries are designed to handle a lot of current without much voltage drop. These are called high-discharge batteries. They have a lot of internal resistance but can provide more current for a longer period of time. Low-discharge batteries have less internal resistance but can't provide as much current for a long period of time.
Le plus ordinateur portable and cell phone batteries are low-discharge batteries. This is why they don't last as long when you use them to power something like a drill. Drill batteries are designed to handle high loads and have a lot of internal resistance, so they don't drop much in voltage under load.
Many types of batteries require a load to maintain their charge. That's why they are referred to as "maintenance-free" or "sealed." They don't need you to do anything except replace them when the power is gone, but this can be very inconvenient. Some battery manufacturers have overcome this problem by using electrolytes that can be pumped out of the battery when it is needed.
What should a 12 volt battery read when under load?
When a battery is under load, the voltage reading will be lower than when it is not. This is because the battery is providing power to something else and is not just sitting idle. The amount of voltage drop will depend on how much current the battery is supplying. A 12 volts battery should read around 11 volts when under load. Keep in mind that this is just a general guideline and may not be accurate for all situations. If you are unsure of what the voltage should be, it is best to consult with a professional.
When it comes to batteries, it is important to understand how they work and what causes them to fail. By understanding these concepts, you can help prolong the life of your battery and make sure that you are getting the most out of it.
The early you catch the issue, the easier and cheaper it is to fix. There are ways to diagnose battery issues, and some of these are doable at home.
You could do a load test on your battery to see if it is dropping voltage under load. A load test will tell you how much power the battery can deliver at a given time. This information can help you determine if your battery is healthy or not. If the voltage drops below 12 volts, then the battery might need to be replaced.
There are visible signs that can show if your battery is failing. For example, sulfation of the plates inside a lead-acid battery usually causes the top part to bulge outwards due to increased internal pressure. This would eventually cause failure and result in an immediate need for replacement.
Another visible sign of a bad or failing voiture battery will be leakage from one end of the battery. If a car is left parked for an extended period of time, then there's a possibility that the acid may escape from one of the cells in the battery and spill onto other parts of your vehicle, such as carpeting or seats.
Therefore, it is important to check these visible signs regularly so you can prevent any damage before it becomes too costly.
If you are not comfortable with doing these at home or don’t have the time to do it yourself, then take your car to a professional mechanic. They can usually diagnose the issue in a few minutes, and you can get your car back on track.